{"id":92707,"date":"2023-07-20T02:14:00","date_gmt":"2023-07-20T00:14:00","guid":{"rendered":"https:\/\/www.sonnenseite.com\/?p=92707"},"modified":"2023-07-19T12:14:56","modified_gmt":"2023-07-19T10:14:56","slug":"bifacial-perovskite-solar-cells-point-to-higher-efficiency","status":"publish","type":"post","link":"https:\/\/www.sonnenseite.com\/en\/science\/bifacial-perovskite-solar-cells-point-to-higher-efficiency\/","title":{"rendered":"Bifacial Perovskite Solar Cells Point to Higher Efficiency"},"content":{"rendered":"\n

NREL Researchers Calculate Boost From Reflected Light Hitting Back of Device.<\/p>\n\n\n\n

A bifacial perovskite solar cell, which allows sunlight to reach both sides of the device, holds the potential to produce higher energy yields at lower overall costs, according to scientists at the U.S. Department of Energy\u2019s National Renewable Energy Laboratory (NREL).<\/p>\n\n\n\n

The dual nature of a bifacial solar cell enables the capture of direct sunlight on the front and the capture of reflected sunlight on the back, allowing this type of device to outperform its monofacial counterparts.<\/p>\n\n\n\n

\u201cThis perovskite cell can operate very effectively from either side,\u201d said Kai Zhu, a senior scientist in the Chemistry and Nanoscience Center at NREL and lead author of a new paper published in the journal Joule<\/em>: \u201cHighly efficient bifacial single-junction perovskite solar cells<\/a>.\u201d His co-authors from NREL are Qi Jiang, Rosemary Bramante, Paul Ndione, Robert Tirawat, and Joseph Berry. Other co-authors are from the University of Toledo.<\/p>\n\n\n\n

Past bifacial perovskite solar cell research has yielded devices considered inadequate in comparison to monofacial cells, which have a current record of 26% efficiency. Ideally, the NREL researchers noted, a bifacial cell should have a front-side efficiency close to the best-performing monofacial cell and a similar back-side efficiency.<\/p>\n\n\n\n

The researchers were able to make a solar cell where the efficiency under illumination from both sides are close together. The lab-measured efficiency of the front illumination reached above 23%. From the back illumination, the efficiency was about 91%\u201393% of the front.<\/p>\n\n\n\n

Before constructing the cell, researchers relied on optical and electrical simulations to determine the necessary thickness. The perovskite layer on the front of the cell had to be sufficiently thick to absorb most of the photons from a certain part of the solar spectrum, but a perovskite layer that is too thick can block the photons. On the back of the cell, the NREL team had to determine the ideal thickness of the rear electrode to minimize resistive loss.<\/p>\n\n\n\n

According to Zhu, simulations guided the design of the bifacial cell, and without that assistance the researchers would have had to experimentally produce cell after cell to determine the ideal thickness. They found the ideal thickness for a perovskite layer is around 850 nanometers. By comparison, a human hair is approximately 70,000 nanometers.<\/p>\n\n\n\n

To evaluate the efficiency gained through bifacial illumination, the researchers placed the cell between two solar simulators. Direct light was aimed at the front side, while the back side received reflected light. The efficiency of the cell climbed as the ratio of reflected light to the front illumination increased.<\/p>\n\n\n\n

While researchers estimate that a bifacial perovskite solar module would cost more to manufacture than a monofacial module, over time bifacial modules could end up being better financial investments because they generate 10%\u201320% more power.<\/p>\n\n\n

Source<\/h5>\r\n\n\n\n

NREL 2023<\/a><\/p>\n

Diese Meldung teilen<\/div>